[Sep-2026] Cisco 300-510 Actual Questions and Braindumps [Q154-Q175]

NO.154 Refer to the exhibit.

A network engineer implemented this segment routing configuration. Which statement about the output is true?

NO.155 What are three requirements for a static IPv6-in-IPv4 tunnel? (Choose three.)

NO.156 Which cost is the default when redistributing routes from BGP to OSPF?

NO.157 Drag and Drop Question
Drag and drop the attributes for the BGP route selection on the left into the correct order on the right. Not all options are used.

NO.158

Refer to the exhibit. Customer A and customer B are connecting through a service provider network with these requirements
* R1 acts as the mapping server to connect 10 0 0.0/30 and 172.16.0.0/30 networks
* R1 and R2 are using nondefault SRG8 range to allocate SID.
* R2 ads as the mapping client for transient traffic originating from customer A Which configuration meets the requirements?

NO.159 What can be used to determine a path from the head-end to a tail-end router when implementing SR-TE with a head-end, with little information on the network topology?

NO.160 Refer to the exhibit.

An engineer is troubleshooting an OSPF issue. Router 1 has a neighbor relationship with router 2. Only router 1 classful EIGRP routes can be seen on router 2. In order for all EIGRP routes to be redistributed correctly, which action should be taken?

NO.161 Refer to the exhibit.

An engineer is troubleshooting an OSPF issue. Router 1 has a neighbor relationship with router 2. Only router 1 classful EIGRP routes can be seen on router 2. In order for all EIGRP routes to be redistributed correctly, which action should be taken?

NO.162 Refer to the exhibit. A regional service provider provides connectivity for a growing enterprise, which recently acquired a new location in a nearby city. The new location, which is connected at CE2. requires connectivity to the company’s data center, which is connected to CE1. The service provider will use VPNv4 to connect the two locations. The networking team is planning to implement segment-routing traffic engineering to route traffic from PE1 to PE2 over a delay- optimized path through P2. Which action must the engineering team take to begin the implementation?

NO.163 Refer to the exhibit.

An engineer has successfully fixed BGP peering issue. R1 has an established eBGP peering with R2 and R3. Which mechanism should the engineer apply in order to steer the traffic correctly?

NO.164 Refer to the exhibit. AJI four routers on the network reside in the same data center. The four routers are running IS-IS between them in Level 1 mode within an IPv4 network. After a network engineer installed several new servers connected to R4, users connected via R1 reported they could not connect to applications on the servers. The engineer has determined that R4 is receiving routes from R3 but it is failing to receive routes from R1. Which action must the engineer take to resolve the issue?

NO.165 Refer to the exhibit. An engineer working for a private telecommunication company with an employee id 4115 46 881 is enabling a segment routing solution with these requirements.
– A service provider is using the default range for prefix SID.
– PE1 must allocate the first SID from the default range for the
loopback address
– PE1 and PE2 loopback SID allocation should have a minimum difference
of 500.
Which configuration must be implemented to meet the requirements?

NO.166 Refer to the exhibit.


Refer to the exhibit. MPLS traffic from 192.168.4.0/24 to 192.168.5.0/24 is failing to pass over the link from R4 to R2. The engineer verified that:
Cisco Express Forwarding Is enabled on all routers.
All routers reach all networks via OSPF.
MPLS traffic from 192.168.1.0/24 to 192.168.3.0/24 is passing normally over the link from R1 to R2.
Which action resolves the issue?

NO.167 Refer to the exhibit. The extension header of the IPv6 header is ignored when which value is equal to zero?

NO.168 Refer to the exhibit.

Refer to the exhibit. After a recent network implementation project, customer A is performing stress testing to verify network redundancy at the branch office connected to R4. When the link from R2 is shut oown as shown, the SLA tracking object fails and the cost of the link between R2 and R4 increases to 100. However, a traceroute operation from a PC in the Branch office shows that traffic to HQ is still routed via R2. Which solution corrects the problem and optimizes traffic flow via R3 without creating operational overhead?

NO.169 Refer to the exhibit.

XR1 and XR2 are sending the prefix 10.11.11.0/24 to XR3. A configured policy on XR1 is incorrectly prepending AS path 11 11 12 12 onto this prefix. A network operator wants to add a policy onto XR3 that will not allow the falsely prepending prefix from being installed. Which policy configuration applied to the XR3 neighbor configuration for XR1 can accomplish this requirement without impact to other or future received routes?

NO.170 Refer to the exhibit.

An engineer is addressing an IS-IS design issue which is running within the topology. All links are running on FastEthernet, except the link between R5 and R4, which is Gigabit Ethernet. Which statement about the design is true?

NO.171 Refer to the exhibit.

Which LSA type is indicated by this router output?

NO.172 Refer to the exhibit.

An engineer applied the configuration on R1 to prevent network 192.168.1.0/24 from being propagated outside of area 5. After the change, users have reported they are not able to access any of the application servers that were working before. While checking the routing table of the peer router. The engineer notices R1 stopped propagating any routes outside are 5. Which action must be taken to fix the problem?

NO.173 What is a feature of SRGB label values?

NO.174 Refer to the exhibit. After these configurations were applied to routers R1 and R2. the two devices cannot form a neighbor relationship What is the reason tor the problem?

NO.175 Refer to the exhibit.

Refer to the exhibit Reuters R2. R3, R4 and R5 all reside in the same area, with R1 in a different area R3 is overutilized and the engineer wants to reduce its CPU load The engineer configured router R4 to summarize routes that it receives from R5. but R3 is still receiving all of the R5 routes. Which action resolves the issue?