Regular Free Updates NS0-194 Dumps Real Exam Questions Test Engine Jul 06, 2022 [Q16-Q35]

Q16. You just set up a new clustered Data ONTAP 8.3 environment and want to monitor volume performance.
Which two commands or products would help you accomplish this task? (Choose two.)

Q17. You perform a security trace when troubleshooting a data access problem for a user. The results are shown in the exhibit.

What should you do to solve this issue?

Q18. What is the minimum number of compute nodes required to run the NetApp Deployment Engine for NetApp HCI?

Q19. Referring to the exhibit.


The exhibit shows an overview of a customer’s network design. The customer is experiencing ping loss. As part of the troubleshooting process, you receive output by using the if grp status command from the node shell.
In this scenario, what is the customer’s problem?

Q20. A customer ordered a FAS2720 cluster with 8 TB SATA drives. The customer wants to use the Advanced Drive Partitioning (ADP) feature to avoid consuming the high capacity drives for the root aggregate. Before you use the cluster setup, you issue the aggr status command and notice that ADP is not being used.
In this scenario, what would you use to implement ADP?

Q21. You want to update your storage system and are concerned about the compatibility of the SAN components and the host environment.
In this scenario, which two actions should you take to verify compatibility? (Choose two.)

Q22. You are using SnapCenter to protect your vCenter virtual machines. You have 10 VMs on one datastore and they are all in the same resource group.
When performing a backup of this resource group, how many Snapshot copies will be created on the ONTAP cluster?

Q23. You observe cyclic redundancy check (CRC) errors on a network port from a node in the cluster.
Which two components would you consider reseating or replacing before you perform actions on the physical port where the errors are reported from the node? (Choose two.)

Q24. After a recent unplanned power outage at the site, the power has been restored and you notice power supply fault messages in the event management system (EMS) log or fault lights on the storage shelves.
Which command would you use to collect information about the problem?

Q25. In ONTAP 9.5, the event log show command queries and displays entries from which file?

Q26. You are using AFF storage with the NVMe storage protocol on your Linux clients.
In this scenario, which NVMe feature must be present and enabled for the client to see storage failover happen?

Q27. An administrator reviewing the message logs for a node notices an instance of a node reporting duplicate IPs for approximately ten seconds. Data access was not reported as interrupted during that time.
In this scenario, which process would generate these messages?

Q28. Several clients are accessing an ONTAP SnapMirror DP destination volume. Some clients frequently access the newest SnapMirror volume data. Accessing this data is much slower when compared to clients that directly access data on the source. You use the wafl scan status command against the destination.
What is a symptom of the problem in this scenario?

Q29. A customer is installing a new system and has determined that they have a broken disk.
What information is required to open a NetApp Support case?

Q30. After a network card was replaced in an ONTAP node, you see the output shown in the exhibit.

What is the problem?

Q31. Click the Exhibit button at the right.
When using ONTAP, the customer uses a mirror-SnapVault cascade, as shown in the exhibit. The Snapshot copies successfully transfer from the primary volume on storage system A to the SnapMirror destination on storage system B.
However, not all SnapMirror Snapshot copies are being transferred from storage system B to the XDP destination on storage system C.

In this scenario, which Snapshot copies will transfer successfully?

Q32. Click the Exhibit button. Your customer explains that his disks are showing 100% utilization, but he does not see very much user I/O. While investigating, you collect statistics using the statit command over a 10-second time period as shown in the exhibit.
In this scenario, what is the problem?

Q33. Exhibit:

A customer receives the AutoSupport message shown below.
”(?] Sat Aug 23 13:00:27 PDT [hostname: env_rngr: callhome.c.fan.fru.fault:error] :
Call home for CHASSIS FAN FRU FAILED: SysFan3 F2 (?] Sat Aug 23 13:00:32
PDT [hostname: env_mgr: monitor.chassisFan.ok:notice]: Chassis fan Sysfan3 F2 is ok”
The output of the sysconfig -a command is shown in the exhibit.
In this scenario, what would you do to solve this problem?

Q34. As part of your backup policy, you configured a local snapshot schedule on your production volume. You review the list of Snapshot copies and you do not see a snapshot from last night.
What are two causes for this problem? (Choose two.)

Q35. Referring to the exhibit.

A database administrator explains that the backup job scheduled to complete by 7:00 AM is not completing as fast as expected. You log in to theFAS3240 system and execute a few commands and obtain the output shown in the exhibit.
Which system resource would you eliminate as a eliminate as a problem based on the command output?