NS0-593 Dumps To Pass Network Appliance Exam in 24 Hours – TestBraindump [Q22-Q38]

Q22. Your customer calls you because one application is not able to access a NetApp ONTAP S3 bucket. While
reviewing the EMS log on the cluster, you see the following message:

The same credentials work in another application.
In this scenario, what would cause this problem?

Q23. A customer calls you to troubleshoot a network issue. The customer wants to create a packet trace for allclients
on the 192.168.9.0/24 subnet.

Referring to the exhibit, on which interface do you have to run the packet trace?

Q24. After expanding a two-node AFF A300 cluster with two AFF A700 nodes, you observe latencies when data is
accessed indirectly. The system node run -node -command netstat command shows retransmits and packet
drops on the LIFs. The AFF A700 nodes with 40 Gbps and the AFF A300 connect with 10 Gbps to the cluster
interconnect. You are using Cisco Nexus 3132Q cluster interconnect switches. You just updated to ONTAP
9.8 software.
In this scenario, what is causing this problem?

Q25. A customer’s storage administrator Informs you about the deactivated Automatic Switchover (AUSO) feature
on their MetroCluster IP environment.
What Information would you tell your customer in this scenario?

Q26. A storage administrator reports that a monitoring toot is reporting that the storage controller reads between
90% to 93% CPU use. You run the sysstat -m command against thenode in question.

Referring to the exhibit, which statement is correct?

Q27. You want to assign storage access to an NVMe protocol host.
Which three objects must beconfigured to accomplish this task? (Choose three.)

Q28. You have a customer who is concerned with high CPU and disk utilization on their SnapMirror destination
system. They are worried about high CPU and disk usage without any user operations.
In this situation, what should you tell the customer?

Q29. After users start reporting the Inability to create new flies in a CIFS share, you find EMS events for
wafl.dir.size.max logged for the volume of the SVM to which the share points.
In this scenario, which action should you take to solve this issue?

Q30. Your customer has mounted an NFS SVM from a Linux client unci performance is very poor. The customer is
certain that they have jumbo frames enabled. They have verified an MTU of 9000 on both the Linux client and
the broadcast domain on the NetApp ONTAP 9.8 cluster.

Referring to the exhibit, which ONTAP command will help isolate a possible MTU mismatch?

Q31. Your customer mentions that they have accidentally destroyed both rootaggregates in their two-node cluster.
In this scenario, what are two actions that must be performed? (Choose two.)

Q32. An administrator receives the following error message:

What are two causes for this error? (Choose two.)

Q33. After a motherboard replacement on a NetApp AFF A300 in a SAN environment, the customer states that
ports 0e and 0f are unable toconnect to the fabric. The ports report “offline”.
What would you examine first to troubleshoot the issue?

Q34. You have a new VMware vSphere cluster with ESXI 7.0U2 hosts. The hosts are connected to a 4-node AFF
A400 NetApp ONTAP9.8 cluster with FC LUNs. You have a requirement to identify and follow I/Os from
each VM on the shared FC LUN-backed datastores for troubleshooting purposes.
In this scenario, which VMware feature Is supported by ONTAP software to accomplish this task?

Q35. A 2-node cluster hosts only NAS data UFs. Allnodes lose access to the cluster network.

Referring to the exhibit, which statement is correct?

Q36. You receive the panic message shown in the exhibit.

In this scenario, which component should you troubleshoot first?

Q37. The motherboard of Node-01 is being replaced. To perform this task, a takeover was Initiated from Node-02.
Node-02 panics showing the string below.
PANIC; Permanent errors on all HA mailbox disks (while marshalling header) in SKprocess
fnmbx_instanceWorker on release 9.5P8 (C)
What has happened in this situation?

Q38. Your customer noticed in NetApp Active IQ that their NetApp Cloud Volumes ONTAP forAzure HA solution
is no longer sending AutoSupport messages over HTTPS. A support ticket has been opened to find out why.
No changes have been made to the Cloud Volumes ONTAP for Azure HA environment.
In this scenario, which two autosupport command parameters should be used to validate that AutoSupport Is
working properly? {Choose two.)