[Full-Version] 2024 New TestBraindump JN0-637 PDF Recently Updated Questions [Q20-Q44]

QUESTION 20
Exhibit

You are using traceoptions to verify NAT session information on your SRX Series device.
Referring to the exhibit, which two statements are correct? (Choose two.)

This is the last packet in the session.

The SRX Series device is performing both source and destination NAT on this session.

This is the first packet in the session.

The SRX Series device is performing only source NAT on this session.

QUESTION 21
Your company uses non-Juniper firewalls and you are asked to provide a Juniper solution for zero-day malware protection.
Which solution would work in this scenario?

Juniper ATP Cloud

Juniper Secure Analytics

Juniper ATP Appliance

Juniper Security Director

QUESTION 22
Exhibit

Referring to the exhibit, which three statements are true? (Choose three.)

The packet’s destination is to an interface on the SRX Series device.

The packet’s destination is to a server in the DMZ zone.

The packet originated within the Trust zone.

The packet is dropped before making an SSH connection.

The packet is allowed to make an SSH connection.

QUESTION 23
Exhibit

You are using ATP Cloud and notice that there is a host with a high number of ETI and C&C hits sourced from the same investigation and notice that some of the events have not been automatically mitigated.
Referring to the exhibit, what is a reason for this behavior?

The C&C events are false positives.

The infected host score is globally set bellow a threat level of 5.

The infected host score is globally set above a threat level of 5.

The ETI events are false positives.

QUESTION 24
Exhibit.

Referring to the exhibit, which two statements are true? (Choose two.)

The configured solution allows IPv6 to IPv4 translation.

The configured solution allows IPv4 to IPv6 translation.

The IPv6 address is invalid.

External hosts cannot initiate contact.

QUESTION 25
Exhibit

Referring to the exhibit, which type of NAT is being performed?

Static NAT

Destination NAT

Persistent NAT

Source NAT

QUESTION 26
Refer to the Exhibit.

Referring to the exhibit, which three topologies are supported by Policy Enforcer? (Choose three.)

Topology 3

Topology 5

Topology 2

Topology 4

Topology 1

QUESTION 27
Which two statements are correct regarding tenant systems on SRX Series devices? (Choose two.)

A maximum of 32 tenant systems can be configured on a physical SRX device.

All tenant systems share a single routing protocol process.

Each tenant system runs its own instance of the routing protocol process

A maximum of 500 tenant systems can be configured on a physical SRX device.

QUESTION 28
You want to use selective stateless packet-based forwarding based on the source address.
In this scenario, which command will allow traffic to bypass the SRX Series device flow daemon?

set firewall family inet filter bypas3_flowd term t1 then virtual-channel stateless

set firewall family inet filter bypass__f lowd term t1 then packet-mode

set firewall family inet filter bypass_flowd term t1 then routing-instance stateless

set firewall family inet filter bypaa3_flowd term t1 then skip-services accept

QUESTION 29
You are asked to detect domain generation algorithms
Which two steps will accomplish this goal on an SRX Series firewall? (Choose two.)

Define an advanced-anti-malware policy under [edit services].

Attach the security-metadata-streaming policy to a security

Define a security-metadata-streaming policy under [edit

Attach the advanced-anti-malware policy to a security policy.

QUESTION 30
Exhibit

An administrator wants to configure an SRX Series device to log binary security events for tenant systems.
Referring to the exhibit, which statement would complete the configuration?

Configure the tenant as TSYS1 for the pi security profile.

Configure the tenant as root for the pi security profile.

Configure the tenant as master for the pi security profile.

Configure the tenant as local for the pi security profile

QUESTION 31
Exhibit.

Referring to the exhibit, which two statements are true? (Choose two.)

Juniper Networks will not investigate false positives generated by this custom feed.

The custom infected hosts feed will not overwrite the Sky ATP infected host’s feed.

The custom infected hosts feed will overwrite the Sky ATP infected host’s feed.

Juniper Networks will investigate false positives generated by this custom feed.

QUESTION 32
Your organization has multiple Active Directory domain to control user access. You must ensure that security polices are passing traffic based upon the user’s access rights.
What would you use to assist your SRX series devices to accomplish this task?

JIMS

Junos Space

JSA

JATP Appliance

QUESTION 33
You have the NAT rule, shown in the exhibit, applied to allow communication across an IPsec tunnel between your two sites with identical networks.
Which statement is correct in this scenario?

The NAT rule with translate the source and destination addresses.

The NAT rule will only translate two addresses at a time.

The NAT rule in applied to the N/A routing instance.

10 packets have been processed by the NAT rule.

QUESTION 34
Which three type of peer devices are supported for Cos-Based IPsec VPN?

High-end SRX Series device

cSRX

vSRX

Branch-end SRX Series devics

QUESTION 35
Which two security intelligence feed types are supported?

infected host feed

Command and Control feed

custom feeds

malicious URL feed

QUESTION 36
Which method does an SRX Series device in transparent mode use to learn about unknown devices in a network?

LLDP-MED

IGMP snooping

RSTP

packet flooding

QUESTION 37
Exhibit

You are trying to configure an IPsec tunnel between SRX Series devices in the corporate office and branch1. You have committed the configuration shown in the exhibit, but the IPsec tunnel is not establishing.
In this scenario, what would solve this problem.

Add multipoint to the st0.0 interface configuration on the branch1 device.

Change the IKE proposal-set to compatible on the branch1 and corporate devices.

Change the local identity to inet advpn on the branch1 device.

Change the IKE mode to aggressive on the branch1 and corporate devices.

QUESTION 38
Exhibit

You are implementing filter-based forwarding to send traffic from the 172.25.0.0/24 network through ISP-
1 while sending all other traffic through your connection to ISP-2. Your ge-0/0/1 interface connects to two networks, including the 172.25.0.0/24 network. You have implemented the configuration shown in the exhibit. The traffic from the 172.25.0.0/24 network is being forwarded as expected to 172.20.0.2, however traffic from the other network (172.25.1.0/24) is not being forwarded to the upstream 172.21.0.2 neighbor.
In this scenario, which action will solve this problem?

You must specify that the 172.25.1.1/24 IP address is the primary address on the ge-0/0/1 interface.

You must apply the firewall filter to the lo0 interface when using filter-based forwarding.

You must add another term to the firewall filter to accept the traffic from the 172.25.1.0/24 network.

You must create the static default route to neighbor 172.21 0.2 under the ISP-1 routing instance hierarchy.

QUESTION 39
You are configuring transparent mode on an SRX Series device. You must permit IP-based traffic only, and BPDUs must be restricted to the VLANs from which they originate.
Which configuration accomplishes these objectives?

QUESTION 40
You are requested to enroll an SRX Series device with Juniper ATP Cloud.
Which statement is correct in this scenario?

If a device is already enrolled in a realm and you enroll it in a new realm, the device data or configuration information is propagated to the new realm.

The only way to enroll an SRX Series device is to interact with the Juniper ATP Cloud Web portal.

When the license expires, the SRX Series device is disenrolled from Juniper ATP Cloud without a grace period

Juniper ATP Cloud uses a Junos OS op script to help you configure your SRX Series device to connect to the Juniper ATP Cloud service.

QUESTION 41
Exhibit.

Referring to the exhibit, a spoke member of an ADVPN is not functioning correctly.
Which two commands will solve this problem? (Choose two.)

[edit interfaces]
user@srx# delete st0.0 multipoint

[edit security ike gateway advpn-gateway]
user@srx# delete advpn partner

[edit security ike gateway advpn-gateway]
user@srx# set version v1-only

[edit security ike gateway advpn-gateway]
user@srx# set advpn suggester disable

QUESTION 42
which security feature bypasses routing or switching lookup?

transparent mode

secure wire

mixed mode

MACsec

QUESTION 43
What are two valid modes for the Juniper ATP Appliance? (Choose two.)

flow collector

event collector

all-in-one

core

QUESTION 44
Exhibit:

You are troubleshooting a firewall filter shown in the exhibit that is intended to log all traffic and block only inbound telnet traffic on interface ge-0/0/3.
How should you modify the configuration to fulfill the requirements?