Pass NSE6_FWF-6.4 Brain Dump Updated Certification Sample Questions [Q16-Q35]

NEW QUESTION 16
A tunnel mode wireless network is configured on a FortiGate wireless controller.
Which task must be completed before the wireless network can be used?

The wireless network interface must be assigned a Layer 3 address

Security Fabric and HTTPS must be enabled on the wireless network interface

The wireless network to Internet firewall policy must be configured

The new network must be manually assigned to a FortiAP profile.

NEW QUESTION 17
Refer to the exhibit.

If the signal is set to -68 dB on the FortiPlanner site survey reading, which statement is correct regarding the coverage area?

Areas with the signal strength weaker than -68 dB are shown with blackbackground.

Areas with the signal strength equal to -68 dB are zoomed in to providebetter visibility.

Areas with the signal strength weaker than -68 dB are highlighted in orangeand red to indicate that no signal was propagated by the APS.

Areas with the signal strength equal or stronger than -68 dB are highlighted in green circles.

NEW QUESTION 18
What type of design model does FortiPlanner use in wireless design project?

Architectural model

Predictive model

Analytical model

Integration model

NEW QUESTION 19
Which two statements about distributed automatic radio resource provisioning (DARRP) are correct? (Choose two.)

DARRP performs continuous spectrum analysis to detect sources of interference. It uses this information to allow the AP to select the optimum channel.

DARRP performs measurements of the number of BSSIDs and their signal strength (RSSI). The controller then uses this information to select the optimum channel for the AP.

DARRP measurements can be scheduled to occur at specific times.

DARRP requires that wireless intrusion detection (WIDS) be enabled to detect neighboring devices.

NEW QUESTION 20
Which statement describes FortiPresence location map functionality?

Provides real-time insight into user movements

Provides real-time insight into user online activity

Provides real-time insight into user purchase activity

Provides real-time insight into user usage stats

NEW QUESTION 21
Which administrative access method must be enabled on a FortiGate interface to allow APs to connect and function?

Security Fabric

SSH

HTTPS

FortiTelemetry

NEW QUESTION 22
Refer to the exhibits.
Exhibit A

Exhibit B

A wireless network has been created to support a group of users in a specific area of a building. The wireless network is configured but users are unable to connect to it. The exhibits show the relevant controller configuration for the APs and the wireless network.
Which two configuration changes will resolve the issue? (Choose two.)

For both interfaces in the wtp-profile, configure set vaps to be “Authors”

Disable intra-vap-privacy for the Authors vap-wireless network

For both interfaces in the wtp-profile, configure vap-all to be manual

Increase the transmission power of the AP radio interfaces

NEW QUESTION 23
Which two phases are part of the process to plan a wireless design project? (Choose two.)

Project information phase

Hardware selection phase

Site survey phase

Installation phase

NEW QUESTION 24
Where in the controller interface can you find a wireless client’s upstream and downstream link rates?

On the AP CLI, using the cw_diag ksta command

On the controller CLI, using the diag wireless-controller wlac -d sta command

On the AP CLI, using the cw_diag -d sta command

On the controller CLI, using the WiFi Client monitor

NEW QUESTION 25
Which two statements about background rogue scanning are correct? (Choose two.)

A dedicated radio configured for background scanning can support the connection of wireless clients

When detecting rogue APs, a dedicated radio configured for background scanning can suppress the rogue AP

Background rogue scanning requires DARRP to be enabled on the AP instance

A dedicated radio configured for background scanning can detect rogue devices on all other channels in its configured frequency band

NEW QUESTION 26
Refer to the exhibit.

If the signal is set to -68 dB on the FortiPlanner site survey reading, which statement is correct regarding the coverage area?

Areas with the signal strength equal to -68 dB are zoomed in to provide better visibility

Areas with the signal strength weaker than -68 dB are cut out of the map

Areas with the signal strength equal or stronger than -68 dB are highlighted in multicolor

Areas with the signal strength weaker than -68 dB are highlighted in orange and red to indicate that no signal was propagated by the APs.

NEW QUESTION 27
When configuring Auto TX Power control on an AP radio, which two statements best describe how the radio responds? (Choose two.)

When the AP detects any other wireless signal stronger that -70 dBm, it will reduce its transmission power until it reaches the minimum configured TX power limit.

When the AP detects PF Interference from an unknown source such as a cordless phone with a signal stronger that -70 dBm, it will increase its transmission power until it reaches the maximum configured TX power limit.

When the AP detects any wireless client signal weaker than -70 dBm, it will reduce its transmission power until it reaches the maximum configured TX power limit.

When the AP detects any interference from a trusted neighboring AP stronger that -70 dBm, it will reduce its transmission power until it reaches the minimum configured TX power limit.

NEW QUESTION 28
Which administrative access method must be enabled on a FortiGate interface to allow APs to connect and function?

Security Fabric Connection

SSH

HTTPS

FortiTelemetry

NEW QUESTION 29
When configuring a wireless network for dynamic VLAN allocation, which three IETF attributes must be supplied by the radius server? (Choose three.)

81 Tunnel-Private-Group-ID

65 Tunnel-Medium-Type

83 Tunnel-Preference

58 Egress-VLAN-Name

64 Tunnel-Type

NEW QUESTION 30
Which statement is correct about security profiles on FortiAP devices?

Security profiles are only supported on Bridge-mode SSIDs.

Security profiles can only be applied via firewall policies on the FortiGate.

Security profiles can only be applied to unencrypted wireless traffic.

Security profiles on FortiAP devices can use FortiGate subscription to inspect the traffic.

NEW QUESTION 31
When using FortiPresence as a captive portal, which two types of public authentication services can be used to access guest Wi-Fi? (Choose two.)

Social networks authentication

Software security token authentication

Short message service authentication

Hardware security token authentication

NEW QUESTION 32
Six APs are located in a remotely based branch office and are managed by a centrally hosted FortiGate. Multiple wireless users frequently connect and roam between the APs in the remote office.
The network they connect to, is secured with WPA2-PSK. As currently configured, the WAN connection between the branch office and the centrally hosted FortiGate is unreliable.
Which configuration would enable the most reliable wireless connectivity for the remote clients?

Configure a tunnel mode wireless network and enable split tunneling to the local network

Configure a bridge mode wireless network and enable the Local standalone configuration option

Configure a bridge mode wireless network and enable the Local authentication configuration option

Install supported FortiAP and configure a bridge mode wireless network

NEW QUESTION 33
Which two phases are part of the process to plan a wireless design project? (Choose two.)

Project information phase

Hardware selection phase

Site survey phase

Installation phase

NEW QUESTION 34
What is the first discovery method used by FortiAP to locate the FortiGate wireless controller in the default configuration?

DHCP

Static

Broadcast

Multicast

NEW QUESTION 35
Refer to the exhibits.
Exhibit A

Exhibit B

Exhibit C

A wireless network has been installed in a small office building and is being used by a business to connect its wireless clients. The network is used for multiple purposes, including corporate access, guest access, and connecting point-of-sale and Io devices.
Users connecting to the guest network located in the reception area are reporting slow performance. The network administrator is reviewing the information shown in the exhibits as part of the ongoing investigation of the problem. They show the profile used for the AP and the controller RF analysis output together with a screenshot of the GUI showing a summary of the AP and its neighboring APs.
To improve performance for the users connecting to the guest network in this area, which configuration change is most likely to improve performance?